1. When cleaning curtain cloth, choose soft cotton cloth to wipe, scratch the appearance with coin very simply, when the stain is too heavy, can use cleaning agent, toothpaste, special cleaning agent, etc. After decontamination, wipe with clean water and then dry. Correct cleaning method can keep the fast rolling shutter door bright as new all the time.

　　2、運用前應由工作人員徹底調試好后，方可對門體進行運轉操作。

　　2. Professional staff should thoroughly debug the door before it is used before it can be operated.

　　3、留意棱角處不要過多的擦磨，否則會造成棱角表皮層掉落。

　　3. Pay attention to the edges and corners do not wear too much, otherwise it will cause the edges and corners of the epidermis to fall off.

　　4、門體在運轉的時分，門體下方制止有小孩或物品，以免運轉過程中傷到小孩或物品。

　　4. When the door body is in operation, stop children or articles under the door body, so as to avoid injuring children or articles during operation.

　　5、應確保電動機在運轉過程中杰出的光滑。一般的電動機運轉5000小時左右，即應彌補或替換光滑脂，運轉中發(fā)現軸承過熱或光滑變質時，液壓及時換光滑脂。替換光滑脂時，應舊的光滑油，并有汽油洗凈軸承及軸承蓋的油槽，然后將ZL-3鋰基脂填充軸承內外圈之間的空腔的1/2(對2極)及2/3(對4、6、8極)。

　　5. It is necessary to ensure the excellent smoothness of the motor during its operation. The general motor runs about 5000 hours, that is, it should make up for or replace the smooth grease. When the bearing is overheated or smooth deterioration is found in operation, the hydraulic pressure should change the smooth grease in time. When replacing the grease, the old grease should be removed, and the oil grooves of the bearing and bearing cover should be washed with gasoline. Then ZL-3 lithium grease should be filled with 1/2 (to 2 poles) and 2/3 (to 4, 6 and 8 poles) of the cavity between the inner and outer rings of the bearing.

　　6、在運轉過程中觀察是否有反常響動，如有反常噪音，需告訴人士進行保護保養(yǎng)。

　　6. Observe if there is any abnormal noise during the operation. If there is abnormal noise, we need to inform professionals for protection and maintenance.

　　7、當電動機的熱保護接連發(fā)作動作時，應查明故障來自電動機還是超負荷或保護裝置整定值太低，故障后，方可投入運轉。

　　7. When the thermal protection of the motor successively breaks out, it should be found out whether the fault comes from the motor or the overload or the setting value of the protection device is too low. After eliminating the fault, it can be put into operation.

　　8、因門體始終處于扭簧拉力狀況，如需修補保護等工作，需聯絡人士操作。

　　8. Because the door body is always in tension condition of torsion spring, if repair and protection are needed, professional personnel should be contacted for operation.

　　卷簾門廠是一家集卷簾門設計、出產、安裝為一體的性企業(yè)。富強以產品質量為確保，以客戶滿意為宗旨，努力開拓市場，產品全省。

　　Yongcheng Rolling Curtain Door Factory is a professional enterprise which integrates design, production and installation of rolling curtain doors. Yongcheng takes product quality as assurance, customer satisfaction as purpose, strives to open up the market, and products are sold well in the whole province.