When repairing the electric rolling gate, the operator must stand in a position where the running status of the rolling gate can be seen, otherwise accidents and damage may occur.

電動卷閘門維修門簾和卷門機禁止與酸堿性物溶液接觸，以防腐蝕門簾表面。

Electric rolling gate maintenance door curtains and rolling gate machines are prohibited from coming into contact with acidic or alkaline solutions to prevent corrosion of the door curtain surface.

所有電動卷閘門維修，啟閉運行方向必須與開關箱指示相同，特別是在新接通電源試車或外來輸入電源變換相線時，應先使用手動裝置將門簾置于門洞高度1/2的位置，接通電源后試操作卷門啟閉，直到與指示相附，方可正常使用，否則損壞限位器，引起卷簾反卷或沖頂?shù)榷斐蓳p失。

All electric roller shutter maintenance, the opening and closing direction must be the same as the indication of the switch box. Especially when testing with a new power supply or changing the phase line with an external input power supply, a manual device should be used to first place the door curtain at a position of 1/2 of the door opening height. After connecting the power supply, the roller shutter should be operated to open and close until it is in compliance with the indication before normal use. Otherwise, the limit device will be damaged, causing the roller shutter to roll back or hit the top, causing losses.

電動卷閘門維修在啟閉停止過程中，應具備隨位停止之功能，不應有停止而繼續下滑現象，如發生下滑距離大于50mm的情況出現，應立即對電動卷閘門維修控制電器和卷門機制動器進行仔細檢查修理，運行正常為止。

During the opening and closing process of the electric rolling gate maintenance, it should have the function of stopping with the position, and there should be no phenomenon of stopping and continuing to slide. If a sliding distance greater than 50mm occurs, the electric rolling gate maintenance control electrical appliances and rolling gate mechanism actuators should be carefully inspected and repaired immediately until they operate normally.

電動卷閘門維修卷門機在運行滑行傳動等部位應定期檢查(少每年2次)，并根據需要及時加油，以保證卷簾門的正常使用。

The electric roller shutter maintenance roller shutter machine should be regularly inspected (at least twice a year) during operation, sliding transmission, and other parts, and timely refueled as needed to ensure the normal use of the roller shutter door.

電動卷閘門維修運行時如有發生較大抖動或異常聲音時應停機檢查，排除有礙門簾正常啟閉的雜物。

If there is significant shaking or abnormal sound during the maintenance and operation of the electric roller shutter, it should be stopped for inspection to eliminate any debris that may hinder the normal opening and closing of the door curtain.

電動卷閘門維修門簾和易銹部部位，應進行定期防腐油漆及保養處理，禁止用重物硬物沖擊門面。

Regular anti-corrosion paint and maintenance treatment should be carried out on the maintenance curtain and rust prone parts of the electric rolling gate. It is prohibited to use heavy or hard objects to impact the door surface.

電動卷閘門維修安裝位置的上端應有可靠的防火設施，在電動卷閘門維修的卷筒下端做包箱或吊頂時必須設置可拆式活動蓋板，在電動卷門機一側下端必須預留500×500mm可拆檢修孔，以便于維修保養。

The upper end of the maintenance and installation position of the electric rolling gate should have reliable fire prevention facilities. When making a packaging box or ceiling at the lower end of the drum for maintenance of the electric rolling gate, a detachable movable cover plate must be installed, and 500 must be reserved at the lower end of one side of the electric rolling gate machine × 500mm detachable access hole for easy maintenance and repair.

電動卷閘門維修底梁座上限位置必須與軸承架下端保持大于200mm的距離，以確保制動停止時不發生沖頂現象。

The upper limit position of the maintenance bottom beam seat of the electric roller gate must be kept at a distance of more than 200mm from the lower end of the bearing frame to ensure that there is no impact phenomenon when braking stops.

以上就濟南卷簾門安裝維修為大家介紹的內容，感謝您在百忙之中查看我公司的信息內容http://ifxf.cn如果您想要了解的更多，歡迎您來電進行咨詢

The above is an introduction to the installation and maintenance of Jinan roller shutter doors. Thank you for taking the time to check our company's information http://ifxf.cn If you want to learn more, please feel free to call for consultation