I believe many people have seen rolling shutter doors. Most of them are used in garage or small shop facade decoration. In the past, rolling shutter doors were usually opened with keys and used manually, but now with remote control rolling shutter doors, it is more convenient to use, but there are many problems in its use.

一、遙控卷簾門的使用

1、 Application of remote control rolling shutter door

1、清碼

1. Clear code

同時按下遙控器上排的兩個按鍵指示燈閃一次后約2秒后快閃即表示清 除成功。清 除之后按遙控器四個按鍵指示燈僅閃一下后熄滅。

Press the two buttons on the upper row of the remote control at the same time, and the indicator light will flash about 2 seconds after flashing once, indicating that the clearing is successful. After clearing, press the four buttons on the remote control, and the indicator light will only flash once and then go out.

2、對拷

2. Torture

將原遙控器與對拷遙控器并排擺放，同時按下兩個遙控器任意按鍵，對拷型遙控器指示燈快閃即表示復制成功。

Place the original remote controller and the copy remote controller side by side, press any key of the two remote controllers at the same time, and the copy remote controller indicator light flashes quickly, which indicates that the copy is successful.

3、恢復

3. Recovery

(1)若誤操作清 除掉有用代碼后，在沒有重新拷貝其他遙控器之前可同時按下遙控器下排兩個按鍵2秒后指示燈快速閃爍則恢復。

(1) If the useful code is cleared by misoperation, the two buttons on the lower row of the remote controller can be pressed at the same time before copying other remote controllers again. After 2 seconds, the indicator light will flash quickly to restore.

(2)新款卷簾門遙控器，四個按鍵分別可以對拷四種不同類型的芯片，也就是一個卷簾門遙控器可以操作四種不同類型的設施。

(2) The new rolling shutter door remote controller, four buttons can copy four different types of chips, that is, a rolling shutter door remote controller can operate four different types of facilities.

4、注意型號

4. Pay attention to the model

確定你的遙控器是哪種遙控器，知道自己遙控器的晶頻型號，芯片型號。

Determine what kind of remote control your remote control is, and know the crystal frequency model and chip model of your remote control.

二、遙控卷簾門的常見問題

2、 Common problems of remote control rolling shutter door

1、電動機不動或轉速慢

1. The motor does not move or the speed is slow

一般是線路斷路、電機燒損、停止按鈕沒復位、限位開關動作、負載較大等引起。

Generally, it is caused by line open circuit, motor burning, no reset of stop button, action of limit switch, large load, etc.

2、控制失效

2. Control failure

繼電器觸點粘死、行程微動開關失效或觸片變形、滑塊緊定螺釘松、靠板螺絲松使靠板移位，使滑塊或螺母不能隨絲桿轉動而移動、限位器傳動齒輪破損、按鈕上、下鍵卡死。

The relay contact is stuck, the travel micro switch is invalid or the contact piece is deformed, the fastening screw of the slide block is loose, the screw of the back plate is loose, which makes the back plate shift, so that the slide block or nut can not move with the screw rod, the transmission gear of the limiter is damaged, and the up and down keys of the button are stuck.

3、手拉鏈不動

3. Hand zipper does not move

環形鏈條堵住十字槽;棘爪無脫離棘輪，壓鏈架卡死。

The ring chain blocks the cross groove; The pawl is not separated from the ratchet wheel, and the chain press frame is stuck.

4、電機振動或噪聲較大

4. The motor has large vibration or noise

剎車盤不平衡或斷裂;剎車盤無緊固;軸承失油或失效，齒輪嚙合不順、失油或磨損嚴重;電機電流聲或振動.

The brake disc is unbalanced or broken; The brake disc is not fastened; Bearing oil loss or failure, gear meshing is not smooth, oil loss or serious wear; Motor current, sound or vibration

5、如果長期缺乏保養，導致電動卷閘門存在的隱患及小故障得不到及時處理，馬達得到一定運行電流后做正向運行，將動力傳給同步帶，再由同步帶將動力傳給吊具系統使門扇開啟。

5. If there is no maintenance for a long time, the hidden dangers and small faults of the electric roller gate can not be dealt with in time. After the motor gets a certain operating current, it will run in a positive direction and transmit the power to the synchronous belt, and then the synchronous belt will transmit the power to the spreader system to open the door leaf.

6、驅動器每年少要加注一次潤滑脂，鏈條應經常加注潤滑油，并檢查各部件磨損情況，磨損嚴重的機件要及時維修或更換。

6. The drive should be filled with lubricating grease at least once a year, the chain should be filled with lubricating oil frequently, and the wear condition of all parts should be checked. The seriously worn parts should be repaired or replaced in time.

以上是遙控卷簾門的使用與常見問題，上述問題希望可以幫到大家。

The above is the use of remote control shutter door and common problems, the above problems can help you.